Polyethylene
HDPE, LDPE and LLDPE resins for film, moulding and pipe.
3 grades
Spec sheet
HDPE Film Grade – typical specification
| Test | Method | Unit | Specification |
|---|---|---|---|
| Melt flow index (190 °C / 5 kg) | ASTM D1238 | g/10 min | 0.25 – 0.35 |
| Density | ASTM D1505 | g/cm³ | 0.950 – 0.953 |
| Tensile strength at yield | ASTM D638 | MPa | Min 25 |
| Elongation at break | ASTM D638 | % | Min 500 |
| Main use | – | – | Blown film, bags |
Typical values. Final specification per offer, contract and COA.
HDPE Blow-Moulding Grade – typical specification
| Test | Method | Unit | Specification |
|---|---|---|---|
| Melt flow index (190 °C / 2.16 kg) | ASTM D1238 | g/10 min | 0.30 – 0.40 |
| Density | ASTM D1505 | g/cm³ | 0.953 – 0.956 |
| Tensile strength at yield | ASTM D638 | MPa | Min 27 |
| Elongation at break | ASTM D638 | % | Min 500 |
| Main use | – | – | Bottles, containers |
Typical values. Final specification per offer, contract and COA.
LDPE Film Grade – typical specification
| Test | Method | Unit | Specification |
|---|---|---|---|
| Melt flow index (190 °C / 2.16 kg) | ASTM D1238 | g/10 min | 0.3 – 2.0 |
| Density | ASTM D1505 | g/cm³ | 0.920 – 0.923 |
| Tensile strength at yield | ASTM D638 | MPa | Min 10 |
| Elongation at break | ASTM D638 | % | Min 400 |
| Main use | – | – | Shrink and general film |
Typical values. Final specification per offer, contract and COA.
LLDPE Film Grade – typical specification
| Test | Method | Unit | Specification |
|---|---|---|---|
| Melt flow index (190 °C / 2.16 kg) | ASTM D1238 | g/10 min | 0.8 – 1.2 |
| Density | ASTM D1505 | g/cm³ | 0.918 – 0.920 |
| Tensile strength at yield | ASTM D638 | MPa | Min 10 |
| Elongation at break | ASTM D638 | % | Min 600 |
| Main use | – | – | Stretch and packaging film |
Typical values. Final specification per offer, contract and COA.
Where it goes
Packaging film and bags
Pipe and fittings
Blow-moulded and injection-moulded products
On request
TDS
Technical data sheet
COA
Lot test results
MSDS
Safety data
Export docs
With every shipment
Product details
Polyethylene (PE) is the most widely used plastic. It is supplied as resin pellets in three main families, each with grades for film, injection moulding, blow moulding, pipe and other processes.
HDPE
High-density polyethylene: stiff and strong. Used for pipe, blow-moulded containers, crates and film.
LDPE
Low-density polyethylene: soft and clear. Used for film, bags, coatings and squeeze bottles.
LLDPE
Linear low-density polyethylene: tough and puncture resistant. Used for stretch film, packaging film and liners.
Melt flow index, density and processing grade are confirmed in the offer.
Available on request.
Request specs / quote
Grade, quantity, destination – we reply with an offer and the spec sheet.
Request specs / quote